GiD forum

Hello,

I have been trying to learn using GID as a post processing
environment. I am interested in the `new' file format
(*.falvia.res) only. So as a start, I wanted to try out the
example available in the online manual:

1- Create the mesh file (*.falvia.msh)
2- Create the result file (*.falvia.res)
3- Load up the mesh file in the 'Preprocess' mode
using the (Files -- Import -- Mesh Read).
4- Move to the 'Postprocess' mode.
5- Try to load up the result file using (Open):::=
GiD complains about reaching the "EOF" in the
second line...!?
6- Assuming there is a problem in reading the blank lines,
I changed the blank lines to comments lines:::=
Gid complains:
(Node out of range: in this line: 9 - Reading Results.)


Any comment is appreciated...
Many thanks
Rajab


P.S.
====

* Both files have been stored under one directory with
the same project name.
** While I was using (copy and past) to create the files,
I noticed a 'typing mistake' in one of the keywords
(i.e. Ntural instead of Natural). Correcting this has not
changed the above at all..
*** I am using (Gid 6.1.2 Academic version) on an SGI workstation,
and I have not experienced any problem with the examples
were included in the download files, or any other file
I have created (i.e. different type of meshes only without
any associated solution).

Hello,

*.flavia.msh
*.flavia.res - the extension '.flavia.' is only used
inside a '*.gid' project to 'automatically' read the results
when passing from pre- to post-.

The new postprocess format can be read with GiD version
6.1.4b or higher, available at:

http://gid.cimne.upc.es/download

under 'Download GiD beta versions', or at:

ftp://gid.cimne.upc.es/pub/gid_adds/

Hope it helps,

miguel

p.s.: Thanks for the 'typing mistake', now is corrected.


Rajab Said wrote:

Hello,

I have been trying to learn using GID as a post processing
environment. I am interested in the `new' file format
(*.falvia.res) only. So as a start, I wanted to try out the
example available in the online manual:

1- Create the mesh file (*.falvia.msh)
2- Create the result file (*.falvia.res)
3- Load up the mesh file in the 'Preprocess' mode
using the (Files -- Import -- Mesh Read).
4- Move to the 'Postprocess' mode.
5- Try to load up the result file using (Open):::=
GiD complains about reaching the "EOF" in the
second line...!?
6- Assuming there is a problem in reading the blank lines,
I changed the blank lines to comments lines:::=
Gid complains:
(Node out of range: in this line: 9 - Reading Results.)

Any comment is appreciated...
Many thanks
Rajab


P.S.
====

* Both files have been stored under one directory with
the same project name.
** While I was using (copy and past) to create the files,
I noticed a 'typing mistake' in one of the keywords
(i.e. Ntural instead of Natural). Correcting this has not
changed the above at all..
*** I am using (Gid 6.1.2 Academic version) on an SGI workstation,
and I have not experienced any problem with the examples
were included in the download files, or any other file
I have created (i.e. different type of meshes only without
any associated solution).

--
--------------------------------------------------------------------------------
Miguel A. de Riera Pasenau miguel at cimne.upc.es http://gid.cimne.upc.es

Hello,

If you want to load files *.flavia.msh and
*.flavia.res in the postprocessor, the easiest way
is:

1- open GiD
2- go to postprocess
3- open either the *.flavia.msh or the *.flavia.res, both
files will be load.

Remember that to use the new Post format it is necessary to
download a recent beta version.

Regards,

--
Compass Ing. y Sistemas Dr. Ramon Ribó
http://www.compassis.com ramsan at compassis.com
c/ Manuel Girona, 61 bajos tel. +34 93 204 10 82
08034 Barcelona, Spain fax. +34 93 204 19 09



-----Mensaje original-----
De: owner-gid at gatxan.cimne.upc.es
[mailto:owner-gid at gatxan.cimne.upc.es]En nombre de Rajab Said
Enviado el: viernes, 28 de septiembre de 2001 12:36
Para: gidlist at gatxan.cimne.upc.es
Asunto: [ GiDlist ] (*.falvia.res) format..?


Hello,

I have been trying to learn using GID as a post processing
environment. I am interested in the `new' file format
(*.falvia.res) only. So as a start, I wanted to try out the
example available in the online manual:

1- Create the mesh file (*.falvia.msh)
2- Create the result file (*.falvia.res)
3- Load up the mesh file in the 'Preprocess' mode
using the (Files -- Import -- Mesh Read).
4- Move to the 'Postprocess' mode.
5- Try to load up the result file using (Open):::=
GiD complains about reaching the "EOF" in the
second line...!?
6- Assuming there is a problem in reading the blank lines,
I changed the blank lines to comments lines:::=
Gid complains:
(Node out of range: in this line: 9 - Reading Results.)


Any comment is appreciated...
Many thanks
Rajab


P.S.
====

* Both files have been stored under one directory with
the same project name.
** While I was using (copy and past) to create the files,
I noticed a 'typing mistake' in one of the keywords
(i.e. Ntural instead of Natural). Correcting this has not
changed the above at all..
*** I am using (Gid 6.1.2 Academic version) on an SGI workstation,
and I have not experienced any problem with the examples
were included in the download files, or any other file
I have created (i.e. different type of meshes only without
any associated solution).