GiD forum

A forum about any subject related to GiD and intending to solve general usage questions and comments about GiD.
https://forum.gidsimulation.com/

[GiDlist] Problem with selecting points

https://forum.gidsimulation.com/viewtopic.php?t=1731

Page 1 of 2

[GiDlist] Problem with selecting points

Posted: Wed Feb 12, 2003 3:22 pm
by Chen Guangjing
Dear Sir/Madam

There is a problem with my GID 6.1.2:
when I select a point from a geometric figure or mesh, the point becomes

red, but the red point is so small that it is difficult to see the red
color clearly.
so could you please do me a favor to tell me how to improve it?
I look forward to your reply!

Yours sincerely,
Chen Gaungjing
Edificio D2

[GiDlist] Problem with selecting points

Posted: Wed Feb 12, 2003 3:46 pm
by Javier Mora
You can use two additional tools:

Utilities - Signal - Points (the point is signed using four lines)
View - Label - All in - Points (you will see a label for each selected
point)

-----Mensaje original-----
 De: gidlist-admin at gatxan.cimne.upc.es
 [mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de Chen Guangjing
 Enviado el: miércoles, 12 de febrero de 2003 15:21
 Para: GiDlist at gatxan.cimne.upc.es
 Asunto: [GiDlist] Problem with selecting points


Dear Sir/Madam

There is a problem with my GID 6.1.2:
 when I select a point from a geometric figure or mesh, the
 point becomes

red, but the red point is so small that it is difficult to see the red
 color clearly.
 so could you please do me a favor to tell me how to improve it?
 I look forward to your reply!

Yours sincerely,
 Chen Gaungjing
 Edificio D2

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

[GiDlist] Problem with selecting points

Posted: Wed Feb 12, 2003 4:04 pm
by Chen Guangjing
Hi, Javier

Many thanks for your reply!
But for me I hope the points selected to be marked by bigger red point.
This problem happened recently, and there was no such problem with my
previous GID.

Chen

Javier Mora wrote:

You can use two additional tools:

Utilities - Signal - Points (the point is signed using four lines)
 View - Label - All in - Points (you will see a label for each selected
 point)

-----Mensaje original-----
 De: gidlist-admin at gatxan.cimne.upc.es
 [mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de Chen Guangjing
 Enviado el: miércoles, 12 de febrero de 2003 15:21
 Para: GiDlist at gatxan.cimne.upc.es
 Asunto: [GiDlist] Problem with selecting points

Dear Sir/Madam
There is a problem with my GID 6.1.2:
 when I select a point from a geometric figure or mesh, the
 point becomes
red, but the red point is so small that it is difficult to see the red
 color clearly.
 so could you please do me a favor to tell me how to improve it?
 I look forward to your reply!
Yours sincerely,
 Chen Gaungjing
 Edificio D2
_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

[GiDlist] Problem with selecting points

Posted: Wed Feb 12, 2003 5:46 pm
by Javier Mora
Other suggestion: check a newer version, GiD7.2 or the last beta version of
GiD6:
ftp://gid.cimne.upc.es/pub/gid_adds/Windows/Old/GiD6.3.0b-win.exe (12.6 MB)


-----Mensaje original-----
 De: gidlist-admin at gatxan.cimne.upc.es
 [mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de Chen Guangjing
 Enviado el: miércoles, 12 de febrero de 2003 16:03
 Para: gidlist at gatxan.cimne.upc.es
 Asunto: Re: [GiDlist] Problem with selecting points


Hi, Javier

Many thanks for your reply!
 But for me I hope the points selected to be marked by bigger
 red point.
 This problem happened recently, and there was no such problem with my
 previous GID.

Chen

Javier Mora wrote:

You can use two additional tools:
Utilities - Signal - Points (the point is signed using four lines)
 View - Label - All in - Points (you will see a label for
 each selected
 point)
-----Mensaje original-----
 De: gidlist-admin at gatxan.cimne.upc.es
 [mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de
 Chen Guangjing
 Enviado el: miércoles, 12 de febrero de 2003 15:21
 Para: GiDlist at gatxan.cimne.upc.es
 Asunto: [GiDlist] Problem with selecting points

Dear Sir/Madam
There is a problem with my GID 6.1.2:
 when I select a point from a geometric figure or mesh, the
 point becomes
red, but the red point is so small that it is difficult
 to see the red
 color clearly.
 so could you please do me a favor to tell me how to improve it?
 I look forward to your reply!
Yours sincerely,
 Chen Gaungjing
 Edificio D2
_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

[GiDlist] help with tcl

Posted: Wed Feb 12, 2003 6:07 pm
by Pablo Perez del Castillo
Hello;
I try to get information about centroid with tcl for every element, so i
write:
*.bas
*loop elems
*set var num=elemsnum
*elemsnum *tcl(WriteCentroidesInfo *num)
*end elems

In the tcl i tried with two ways, with "regexp" and with "split " and
"lindex". With "regexp" i got error in variable $b, with "split" amd
"lindex" i get like this: center=2.22281

proc WriteCentroidesInfo {num} {
set a [.central.s info listMassProperties Elements $num]
regexp -nocase {Gravity center= ([0-9]+)} $a none b
return $b
#set b [split $a]
#set x [lindex $b 9]
#return $x
#set y [lindex $b 10]
#return $y
#set z [lindex $b 11]
#return $z

}

What is my mistake?, advanced thanks
Pablo

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20030212/d238d641/attachment.htm

[GiDlist] Problem with selecting points

Posted: Wed Feb 12, 2003 6:11 pm
by Chen Guangjing
Many thanks, but this problem still exists for both GID6.3.0b and GID7.2.
When I want to create a line, I just wish its two boundary points to be bigger.

Chen

Javier Mora wrote:

Other suggestion: check a newer version, GiD7.2 or the last beta version of
 GiD6:
 ftp://gid.cimne.upc.es/pub/gid_adds/Windows/Old/GiD6.3.0b-win.exe (12.6 MB)

-----Mensaje original-----
 De: gidlist-admin at gatxan.cimne.upc.es
 [mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de Chen Guangjing
 Enviado el: miércoles, 12 de febrero de 2003 16:03
 Para: gidlist at gatxan.cimne.upc.es
 Asunto: Re: [GiDlist] Problem with selecting points

Hi, Javier
Many thanks for your reply!
 But for me I hope the points selected to be marked by bigger
 red point.
 This problem happened recently, and there was no such problem with my
 previous GID.
Chen
Javier Mora wrote:
You can use two additional tools:
Utilities - Signal - Points (the point is signed using four lines)
 View - Label - All in - Points (you will see a label for
 each selected
 point)
-----Mensaje original-----
 De: gidlist-admin at gatxan.cimne.upc.es
 [mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de
 Chen Guangjing
 Enviado el: miércoles, 12 de febrero de 2003 15:21
 Para: GiDlist at gatxan.cimne.upc.es
 Asunto: [GiDlist] Problem with selecting points

Dear Sir/Madam
There is a problem with my GID 6.1.2:
 when I select a point from a geometric figure or mesh, the
 point becomes
red, but the red point is so small that it is difficult
 to see the red
 color clearly.
 so could you please do me a favor to tell me how to improve it?
 I look forward to your reply!
Yours sincerely,
 Chen Gaungjing
 Edificio D2
_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist
_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

[GiDlist] Problem with selecting points

Posted: Wed Feb 12, 2003 7:19 pm
by Enrique Escolano
For the next beta version, we are working in a "custom render" mode.
The user can create more "user-defined" render modes, setting some options:
point and line size, color by layer or by entity type, etc.

Enrique Escolano

----- Original Message -----
From: "Chen Guangjing" chen.guangjing at upc.es
To: gidlist at gatxan.cimne.upc.es
Sent: Wednesday, February 12, 2003 6:10 PM
Subject: Re: [GiDlist] Problem with selecting points


Many thanks, but this problem still exists for both GID6.3.0b and GID7.2.
 When I want to create a line, I just wish its two boundary points to be
bigger.

Chen

Javier Mora wrote:

Other suggestion: check a newer version, GiD7.2 or the last beta version
of
GiD6:
 ftp://gid.cimne.upc.es/pub/gid_adds/Windows/Old/GiD6.3.0b-win.exe (12.6
MB)

-----Mensaje original-----
 De: gidlist-admin at gatxan.cimne.upc.es
 [mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de Chen Guangjing
 Enviado el: miércoles, 12 de febrero de 2003 16:03
 Para: gidlist at gatxan.cimne.upc.es
 Asunto: Re: [GiDlist] Problem with selecting points

Hi, Javier
Many thanks for your reply!
 But for me I hope the points selected to be marked by bigger
 red point.
 This problem happened recently, and there was no such problem with my
 previous GID.
Chen
Javier Mora wrote:
You can use two additional tools:
Utilities - Signal - Points (the point is signed using four lines)
 View - Label - All in - Points (you will see a label for
 each selected
 point)
-----Mensaje original-----
 De: gidlist-admin at gatxan.cimne.upc.es
 [mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de
 Chen Guangjing
 Enviado el: miércoles, 12 de febrero de 2003 15:21
 Para: GiDlist at gatxan.cimne.upc.es
 Asunto: [GiDlist] Problem with selecting points

Dear Sir/Madam
There is a problem with my GID 6.1.2:
 when I select a point from a geometric figure or mesh, the
 point becomes
red, but the red point is so small that it is difficult
 to see the red
 color clearly.
 so could you please do me a favor to tell me how to improve it?
 I look forward to your reply!
Yours sincerely,
 Chen Gaungjing
 Edificio D2
_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist
_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

[GiDlist] Problem with selecting points

Posted: Wed Feb 12, 2003 7:41 pm
by Chen Guangjing
Many thanks!
I know where to change the color of point, line, etc., but I don't know where to
change point size.
If you could tell me it will be much appreciated!

Chen

Enrique Escolano wrote:

For the next beta version, we are working in a "custom render" mode.
 The user can create more "user-defined" render modes, setting some options:
 point and line size, color by layer or by entity type, etc.

Enrique Escolano

----- Original Message -----
 From: "Chen Guangjing" chen.guangjing at upc.es
 To: gidlist at gatxan.cimne.upc.es
 Sent: Wednesday, February 12, 2003 6:10 PM
 Subject: Re: [GiDlist] Problem with selecting points

Many thanks, but this problem still exists for both GID6.3.0b and GID7.2.
 When I want to create a line, I just wish its two boundary points to be
 bigger.
Chen
Javier Mora wrote:
Other suggestion: check a newer version, GiD7.2 or the last beta version
 of
 GiD6:
 ftp://gid.cimne.upc.es/pub/gid_adds/Windows/Old/GiD6.3.0b-win.exe (12.6
 MB)
-----Mensaje original-----
 De: gidlist-admin at gatxan.cimne.upc.es
 [mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de Chen Guangjing
 Enviado el: miércoles, 12 de febrero de 2003 16:03
 Para: gidlist at gatxan.cimne.upc.es
 Asunto: Re: [GiDlist] Problem with selecting points

Hi, Javier
Many thanks for your reply!
 But for me I hope the points selected to be marked by bigger
 red point.
 This problem happened recently, and there was no such problem with my
 previous GID.
Chen
Javier Mora wrote:
You can use two additional tools:
Utilities - Signal - Points (the point is signed using four lines)
 View - Label - All in - Points (you will see a label for
 each selected
 point)
-----Mensaje original-----
 De: gidlist-admin at gatxan.cimne.upc.es
 [mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de
 Chen Guangjing
 Enviado el: miércoles, 12 de febrero de 2003 15:21
 Para: GiDlist at gatxan.cimne.upc.es
 Asunto: [GiDlist] Problem with selecting points

Dear Sir/Madam
There is a problem with my GID 6.1.2:
 when I select a point from a geometric figure or mesh, the
 point becomes
red, but the red point is so small that it is difficult
 to see the red
 color clearly.
 so could you please do me a favor to tell me how to improve it?
 I look forward to your reply!
Yours sincerely,
 Chen Gaungjing
 Edificio D2
_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist
_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist
_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

[GiDlist] help with tcl

Posted: Wed Feb 12, 2003 7:57 pm
by Enrique Escolano
Your regexp only expects "Gravity center=" and next a integer value (a string with numeric characters), but in this
case, the coordinates are real numbers (a real number can contain [0-9],+,-,.,E).
Use for example this regexp:

proc WriteCentroidesInfo {num} {
set a [.central.s info listMassProperties Elements $num]
regexp {Gravity center=([0-9.+eE-]+) ([0-9.+eE-]+) ([0-9.+eE-]+)} $a {} x y z
return "$x $y $z"
}

Enrique
----- Original Message -----
From: Pablo Perez del Castillo
To: gidlist at gatxan.cimne.upc.es
Sent: Thursday, February 13, 2003 12:59 AM
Subject: [GiDlist] help with tcl


Hello;
I try to get information about centroid with tcl for every element, so i write:
*.bas
*loop elems
*set var num=elemsnum
*elemsnum *tcl(WriteCentroidesInfo *num)
*end elems
In the tcl i tried with two ways, with "regexp" and with "split " and "lindex". With "regexp" i got error in variable $b, with "split" amd "lindex" i get like this: center=2.22281

proc WriteCentroidesInfo {num} {
set a [.central.s info listMassProperties Elements $num]
regexp -nocase {Gravity center= ([0-9]+)} $a none b
return $b
#set b [split $a]
#set x [lindex $b 9]
#return $x
#set y [lindex $b 10]
#return $y
#set z [lindex $b 11]
#return $z

}

What is my mistake?, advanced thanks
Pablo


-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20030212/c8e75046/attachment.htm

[GiDlist] Problem with selecting points

Posted: Wed Feb 12, 2003 7:58 pm
by Enrique Escolano
Until this future beta version, the point size cannot be changed.

Enrique
----- Original Message -----
From: "Chen Guangjing" chen.guangjing at upc.es
To: gidlist at gatxan.cimne.upc.es
Sent: Wednesday, February 12, 2003 7:39 PM
Subject: Re: [GiDlist] Problem with selecting points


Many thanks!
 I know where to change the color of point, line, etc., but I don't know
where to
change point size.
 If you could tell me it will be much appreciated!

Chen

Enrique Escolano wrote:

For the next beta version, we are working in a "custom render" mode.
 The user can create more "user-defined" render modes, setting some
options:
point and line size, color by layer or by entity type, etc.
Enrique Escolano
----- Original Message -----
 From: "Chen Guangjing" chen.guangjing at upc.es
 To: gidlist at gatxan.cimne.upc.es
 Sent: Wednesday, February 12, 2003 6:10 PM
 Subject: Re: [GiDlist] Problem with selecting points
Many thanks, but this problem still exists for both GID6.3.0b and
GID7.2.
When I want to create a line, I just wish its two boundary points to
be
bigger.
Chen
Javier Mora wrote:
Other suggestion: check a newer version, GiD7.2 or the last beta
version
of
 GiD6:
 ftp://gid.cimne.upc.es/pub/gid_adds/Windows/Old/GiD6.3.0b-win.exe
(12.6
MB)
-----Mensaje original-----
 De: gidlist-admin at gatxan.cimne.upc.es
 [mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de Chen
Guangjing
Enviado el: miércoles, 12 de febrero de 2003 16:03
 Para: gidlist at gatxan.cimne.upc.es
 Asunto: Re: [GiDlist] Problem with selecting points

Hi, Javier
Many thanks for your reply!
 But for me I hope the points selected to be marked by bigger
 red point.
 This problem happened recently, and there was no such problem with
my
previous GID.
Chen
Javier Mora wrote:
You can use two additional tools:
Utilities - Signal - Points (the point is signed using four
lines)
View - Label - All in - Points (you will see a label for
 each selected
 point)
-----Mensaje original-----
 De: gidlist-admin at gatxan.cimne.upc.es
 [mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de
 Chen Guangjing
 Enviado el: miércoles, 12 de febrero de 2003 15:21
 Para: GiDlist at gatxan.cimne.upc.es
 Asunto: [GiDlist] Problem with selecting points

Dear Sir/Madam
There is a problem with my GID 6.1.2:
 when I select a point from a geometric figure or mesh, the
 point becomes
red, but the red point is so small that it is difficult
 to see the red
 color clearly.
 so could you please do me a favor to tell me how to improve
it?
I look forward to your reply!
Yours sincerely,
 Chen Gaungjing
 Edificio D2
_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist
_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist
_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

_______________________________________________
 GiDlist mailing list
 GiDlist at gid.cimne.upc.es
 http://gid.cimne.upc.es/mailman/listinfo/gidlist

All times are UTC+01:00
Page 1 of 2

Powered by phpBB® Forum Software © phpBB Limited