GiD forum

Dear GID team,

Attached is a gid project, I couldn't mesh it because GID complaining about
some contour errors. Could you please tell me how to avoid such problem.

Attache is the project.
Thank you


Khaled Obeidat
Research Engineer
EMAG Technologies, Inc.
www.emagtechnologies.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20040303/ddcf1c7a/attachment.htm
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Ship.zip
Type: application/zip
Size: 52944 bytes
Desc: not available
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20040303/ddcf1c7a/attachment.zip

Can any one please answer my question?


At 01:46 PM 3/3/2004, you wrote:
Dear GID team,

Attached is a gid project, I couldn't mesh it because GID complaining
about some contour errors. Could you please tell me how to avoid such problem.

Attache is the project.
Thank you

Khaled Obeidat
Research Engineer
EMAG Technologies, Inc.
www.emagtechnologies.com

Khaled Obeidat
Research Engineer
EMAG Technologies, Inc.
www.emagtechnologies.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20040315/c373a292/attachment.htm

Hello,

GiD point mesher has some limits in the number of points that can
generate. It will be corrected
in the following versions.

Regards,

--
Compass Ing. y Sistemas Dr. Ramon Ribo
http://www.compassis.com http://www.compassis.com/
ramsan at compassis.com
c/ Manuel Girona, 61 bajos tel. +34 93 204 10 82
08034 Barcelona, Spain fax. +34 93 204 19 09

-----Mensaje original-----
De: gidlist-admin at gatxan.cimne.upc.es
[mailto:gidlist-admin at gatxan.cimne.upc.es] En nombre de Khaled Obeidat
Enviado el: lunes, 15 de marzo de 2004 15:13
Para: gidlist at gatxan.cimne.upc.es
Asunto: Re: [GiDlist] Point mesh problem


Can any one please answer my question?


At 01:46 PM 3/3/2004, you wrote:


Dear GID team,

Attached is a gid project, I couldn't mesh it because GID complaining
about some contour errors. Could you please tell me how to avoid such
problem.

Attache is the project.
Thank you

Khaled Obeidat
Research Engineer
EMAG Technologies, Inc.
www.emagtechnologies.com http://www.emagtechnologies.com/


Khaled Obeidat
Research Engineer
EMAG Technologies, Inc.
www.emagtechnologies.com http://www.emagtechnologies.com/


-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20040315/b46b924b/attachment.htm

MensajeTo avoid this limited number of 1-noded elements, try to divide your volume in smaller volumes.

Enrique Escolano
----- Original Message -----
From: Ramon Ribó
To: gidlist at gatxan.cimne.upc.es
Sent: Monday, March 15, 2004 4:54 PM
Subject: RE: [GiDlist] Point mesh problem



Hello,

GiD point mesher has some limits in the number of points that can generate. It will be corrected
in the following versions.

Regards,
--
Compass Ing. y Sistemas Dr. Ramon Ribo
http://www.compassis.com ramsan at compassis.com
c/ Manuel Girona, 61 bajos tel. +34 93 204 10 82
08034 Barcelona, Spain fax. +34 93 204 19 09

-----Mensaje original-----
De: gidlist-admin at gatxan.cimne.upc.es [mailto:gidlist-admin at gatxan.cimne.upc.es] En nombre de Khaled Obeidat
Enviado el: lunes, 15 de marzo de 2004 15:13
Para: gidlist at gatxan.cimne.upc.es
Asunto: Re: [GiDlist] Point mesh problem


Can any one please answer my question?


At 01:46 PM 3/3/2004, you wrote:

Dear GID team,

Attached is a gid project, I couldn't mesh it because GID complaining about some contour errors. Could you please tell me how to avoid such problem.

Attache is the project.
Thank you

Khaled Obeidat
Research Engineer
EMAG Technologies, Inc.
www.emagtechnologies.com

Khaled Obeidat
Research Engineer
EMAG Technologies, Inc.
www.emagtechnologies.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20040315/8cb124f7/attachment.htm